Obama Will be Remembered as Don Quixote, the man that "Tilted at Windmills"
President Obama, NOT THAT LONG AGO, sat in for Don Quixote "The Man of
LaMancha" at a press conference at the plant of a Spanish wind generator
manufacturer. He continues to be out of touch with reality "Tilting at
windmills" when he should be paying attention to easing the regulation
on domestic fossil fuels. Domestic fossil fuels are the answer to our
energy problems; not Wind Generation.
Fossil Fuels are so abundant upon the Earth because God provided, in
His infinite wisdom, fossil fuels for Man's energy needs. It's certainly
not an accident. The fact that we choose not to use them is simply
intellectual stupidity on the part of an elite group of people within
our society.
The fact that fossil fuels are so abundant, it is safe to
have faith that their utilization was part of God's plan for mankind
from the beginning.
Contrary to popular belief the economic problems within this Country
are caused, in whole, by our National Energy Policy. Yes, they will
tell you that there is no Energy Policy when, in fact, that is far from
the truth.
The intent of our Government is, through legislation and policy
setting to restrict the production and or block altogether the use of
traditional energy sources. Why is this being done? Because there is
great wealth to be made by those promoting "green power". It's all about the wealth to be acquired by this special interest group.
Green power sources should rightfully be part of the energy mix, but
can never be the provider of the base commercial and industrial power
needs of an industrialized economy. The intent of the Green special
interests is to drive up the cost of fossil fuels to the point that
Green energy can be competitive. The problem is, it is bankrupting the
country for the benefit of this group of people.
We the American people must demand that this strategy be abandoned
and we begin to use the God given resources that we posses is abundance.
Yes: Coal, Oil, Natural Gas and Nuclear.
We must demand it today. We must get our economy back on track. Every
day we wait, we are closer to national bankruptcy. Write your
congressmen and senators today. Let's start to put real unrelenting
pressure on Washington today. Our economy could be turned around in a
matter of months if we could again start to use coal and step up the
production of oil in existing fields where production is prohibited.
Say No to foreign oil, Say Yes to Domestic Energy sources.
I invite your comments
Tony Whyte
MAN OF LA MANCHA
"Don Quixote." His dream is Everyman's dream. His tilting at windmills is Everyman's great adventure.
Thursday, October 25, 2012
YOU CAN'T FIND A WIDE GATE PRODUCT THAT ACTUALLY PERFORMS AT A HOME IMPROVEMENT STORE
AN AMERICAN COMPANY MAKING AMERICAN PRODUCTS
Quote: from customer: "Tony, gate is awesome. for sure gonna be using your services in the future. awesome design. easy install. love it."
THE 4TH DIMENSION IS PERFORMANCE
Victoria House Company
is the Manufacturer and Distributer of GateBuilder Gate Frames
We are a family owned and operated business located in
Alpine, California, a small community east of San Diego, Ca. We are the
manufacturer and distributor of Southern Crossings Gate products. It
has been our goal from the beginning, to offer attractive, high
quality, top-of-the-line products at reasonable pricing.
We are building this business in a world where it is often
difficult to discern if a business is legitimate and honest. People
tend make their purchases from large companies like Home Depot or
Lowes because they feel that they can trust them to stand behind the
products they offer for sale only to find out that the products are
often mediocre and only subject to the warrantys of the companies
manufacturing the product.
We manufacture superior products are built with heavy duty
materials and are absolutely guaranteed not to sag. In addition, all
parts are either Coated with a Superior Coating Product or zinc plated
for long lasting beauty.
Our gate products are also head and shoulders above other
well known manufacturers that offer their products for sale on the
internet.
We absolutely guarantee our products and stand behind our products 100%
If We Say It, "Consider it Done"
We hope you will order our gate products with the confidence
that you will actually get what you paid for and that they will
perform as promised.
We will provide you with references of satisfied customers upon request.
Tony & Diana Whyte
Owners - The Victoria House Company
Owners - The Victoria House Company
GateBuilder Gate Frames
Lasting Performance
Assembles & Installs Like Magic Designed by a Former Gate Installer
Who Figured out How to Do It Better
Imagine a Gate that will never Sag
We Make the Frame, Supply the Hardware!
You do the Fun Part, the Art Work when you apply the Facing Materials!
You Will Find GateBuilder Gate Frames are Better Than You Ever Expected
View a Customers Side Show of a Beautiful Wooden Gate that He Built on GateBuilder Frames
The Wooden Fencing Panels Utilized on these Gates Were Purchased from Home Depot
Mounted on a GateBuilder 'X' Gate 16' Modular Frame
Contractors & Gate Builders,
I'm Tony Whyte Owner & General Manager of the
Victoria House Company. We Manufacture Gates under the Trade Names
Southern Crossings Gates & GateBuilder Gate Frames.
We have superior products that are not well known. We
have exhibited from time to time at Home Shows and the Southern
California Landscape Contractors Expo. Our products have been well
received and it's time to broaden our product reach.
The modularity of our frames is its real strength. The
system is stronger than welded frames and much easier to install.
Because our frames are modular they are also well suited to shipping at
reasonable cost.
GateBuilder Frames are superior in strength because they
are a true truss system as would be engineered for roof trusses or
bridge construction. They are built of heavy duty materials that
parlay into an amazingly light Wooden Gate once the wood facing
material is applied. A GateBuilder frame is guaranteed not to sag
and will outlast many generations of refacing.
If you are a Contractor, you have never installed a gate that will be easier or better performing.
We would like to be your Gate Supplier of Choice - Please give me a call
619 729 0420 or 619 445 8550
Sincerely,
Tony Whyte
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Happiness is Building a Gate With a GateBuilder Gate Frame
Fully Adjustable to fit your gate opening!
Order Today RIGHT NOW!
Includes the Cost of Shipping
619 445 1135 619 729-0420
gatebuilder@hotmail.com
WE NOT ONLY HAVE THE BEST PRODUCTS - WE HAVE THE BEST SERVICE!
AN AMERICAN COMPANY MAKING AMERICAN PRODUCTS
Quote: from customer: "Tony, gate is awesome. for sure gonna be using your services in the future. awesome design. easy install. love it."
THE 4TH DIMENSION IS PERFORMANCE
Victoria House Company
is the Manufacturer and Distributer of GateBuilder Gate Frames
We are a family owned and operated business located in
Alpine, California, a small community east of San Diego, Ca. We are the
manufacturer and distributor of Southern Crossings Gate products. It
has been our goal from the beginning, to offer attractive, high
quality, top-of-the-line products at reasonable pricing.
We are building this business in a world where it is often
difficult to discern if a business is legitimate and honest. People
tend make their purchases from large companies like Home Depot or
Lowes because they feel that they can trust them to stand behind the
products they offer for sale only to find out that the products are
often mediocre and only subject to the warrantys of the companies
manufacturing the product.
We manufacture superior products are built with heavy duty
materials and are absolutely guaranteed not to sag. In addition, all
parts are either Coated with a Superior Coating Product or zinc plated
for long lasting beauty.
Our gate products are also head and shoulders above other
well known manufacturers that offer their products for sale on the
internet.
We absolutely guarantee our products and stand behind our products 100%
If We Say It, "Consider it Done"
We hope you will order our gate products with the confidence
that you will actually get what you paid for and that they will
perform as promised.
We will provide you with references of satisfied customers upon request.
Tony & Diana Whyte
Owners - The Victoria House Company
Owners - The Victoria House Company
GateBuilder Gate Frames
Lasting Performance
Assembles & Installs Like Magic Designed by a Former Gate Installer
Who Figured out How to Do It Better
Imagine a Gate that will never SagWe Make the Frame, Supply the Hardware!
You do the Fun Part, the Art Work when you apply the Facing Materials!
You Will Find GateBuilder Gate Frames are Better Than You Ever Expected
View a Customers Side Show of a Beautiful Wooden Gate that He Built on GateBuilder Frames
The Wooden Fencing Panels Utilized on these Gates Were Purchased from Home Depot
Mounted on a GateBuilder 'X' Gate 16' Modular Frame
Contractors & Gate Builders,
I'm Tony Whyte Owner & General Manager of the
Victoria House Company. We Manufacture Gates under the Trade Names
Southern Crossings Gates & GateBuilder Gate Frames.
We have superior products that are not well known. We
have exhibited from time to time at Home Shows and the Southern
California Landscape Contractors Expo. Our products have been well
received and it's time to broaden our product reach.
The modularity of our frames is its real strength. The
system is stronger than welded frames and much easier to install.
Because our frames are modular they are also well suited to shipping at
reasonable cost.
GateBuilder Frames are superior in strength because they
are a true truss system as would be engineered for roof trusses or
bridge construction. They are built of heavy duty materials that
parlay into an amazingly light Wooden Gate once the wood facing
material is applied. A GateBuilder frame is guaranteed not to sag
and will outlast many generations of refacing.
If you are a Contractor, you have never installed a gate that will be easier or better performing.
We would like to be your Gate Supplier of Choice - Please give me a call
619 729 0420 or 619 445 8550
Sincerely,
Tony Whyte
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Happiness is Building a Gate With a GateBuilder Gate Frame
Fully Adjustable to fit your gate opening!
Order Today RIGHT NOW!
Includes the Cost of Shipping
619 445 1135 619 729-0420
gatebuilder@hotmail.com
THE BEST APPROACH TO GATE BUILDING EVER DEVISED
AN AMERICAN COMPANY MAKING AMERICAN PRODUCTS
Quote: from customer: "Tony, gate is awesome. for sure gonna be using your services in the future. awesome design. easy install. love it."
THE 4TH DIMENSION IS PERFORMANCE
Victoria House Company
is the Manufacturer and Distributer of GateBuilder Gate Frames
We are a family owned and operated business located in
Alpine, California, a small community east of San Diego, Ca. We are the
manufacturer and distributor of Southern Crossings Gate products. It
has been our goal from the beginning, to offer attractive, high
quality, top-of-the-line products at reasonable pricing.
We are building this business in a world where it is often
difficult to discern if a business is legitimate and honest. People
tend make their purchases from large companies like Home Depot or
Lowes because they feel that they can trust them to stand behind the
products they offer for sale only to find out that the products are
often mediocre and only subject to the warrantys of the companies
manufacturing the product.
We manufacture superior products are built with heavy duty
materials and are absolutely guaranteed not to sag. In addition, all
parts are either Coated with a Superior Coating Product or zinc plated
for long lasting beauty.
Our gate products are also head and shoulders above other
well known manufacturers that offer their products for sale on the
internet.
We absolutely guarantee our products and stand behind our products 100%
If We Say It, "Consider it Done"
We hope you will order our gate products with the confidence
that you will actually get what you paid for and that they will
perform as promised.
We will provide you with references of satisfied customers upon request.
Tony & Diana Whyte
Owners - The Victoria House Company
Owners - The Victoria House Company
GateBuilder Gate Frames
Lasting Performance
Assembles & Installs Like Magic Designed by a Former Gate Installer
Who Figured out How to Do It Better
Imagine a Gate that will never SagWe Make the Frame, Supply the Hardware!
You do the Fun Part, the Art Work when you apply the Facing Materials!
You Will Find GateBuilder Gate Frames are Better Than You Ever Expected
View a Customers Side Show of a Beautiful Wooden Gate that He Built on GateBuilder Frames
The Wooden Fencing Panels Utilized on these Gates Were Purchased from Home Depot
Mounted on a GateBuilder 'X' Gate 16' Modular Frame
Contractors & Gate Builders,
I'm Tony Whyte Owner & General Manager of the
Victoria House Company. We Manufacture Gates under the Trade Names
Southern Crossings Gates & GateBuilder Gate Frames.
We have superior products that are not well known. We
have exhibited from time to time at Home Shows and the Southern
California Landscape Contractors Expo. Our products have been well
received and it's time to broaden our product reach.
The modularity of our frames is its real strength. The
system is stronger than welded frames and much easier to install.
Because our frames are modular they are also well suited to shipping at
reasonable cost.
GateBuilder Frames are superior in strength because they
are a true truss system as would be engineered for roof trusses or
bridge construction. They are built of heavy duty materials that
parlay into an amazingly light Wooden Gate once the wood facing
material is applied. A GateBuilder frame is guaranteed not to sag
and will outlast many generations of refacing.
If you are a Contractor, you have never installed a gate that will be easier or better performing.
We would like to be your Gate Supplier of Choice - Please give me a call
619 729 0420 or 619 445 8550
Sincerely,
Tony Whyte
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Happiness is Building a Gate With a GateBuilder Gate Frame
Fully Adjustable to fit your gate opening!
Order Today RIGHT NOW!
Includes the Cost of Shipping
619 445 1135 619 729-0420
gatebuilder@hotmail.com
SIMPLY THE BETTER CHOICE IN GATE PRODUCTS
AN AMERICAN COMPANY MAKING AMERICAN PRODUCTS
Quote: from customer: "Tony, gate is awesome. for sure gonna be using your services in the future. awesome design. easy install. love it."
THE 4TH DIMENSION IS PERFORMANCE
Victoria House Company
is the Manufacturer and Distributer of GateBuilder Gate Frames
We are a family owned and operated business located in
Alpine, California, a small community east of San Diego, Ca. We are the
manufacturer and distributor of Southern Crossings Gate products. It
has been our goal from the beginning, to offer attractive, high
quality, top-of-the-line products at reasonable pricing.
We are building this business in a world where it is often
difficult to discern if a business is legitimate and honest. People
tend make their purchases from large companies like Home Depot or
Lowes because they feel that they can trust them to stand behind the
products they offer for sale only to find out that the products are
often mediocre and only subject to the warrantys of the companies
manufacturing the product.
We manufacture superior products are built with heavy duty
materials and are absolutely guaranteed not to sag. In addition, all
parts are either Coated with a Superior Coating Product or zinc plated
for long lasting beauty.
Our gate products are also head and shoulders above other
well known manufacturers that offer their products for sale on the
internet.
We absolutely guarantee our products and stand behind our products 100%
If We Say It, "Consider it Done"
We hope you will order our gate products with the confidence
that you will actually get what you paid for and that they will
perform as promised.
We will provide you with references of satisfied customers upon request.
Tony & Diana Whyte
Owners - The Victoria House Company
Owners - The Victoria House Company
GateBuilder Gate Frames
Lasting Performance
Assembles & Installs Like Magic Designed by a Former Gate Installer
Who Figured out How to Do It Better
Imagine a Gate that will never SagWe Make the Frame, Supply the Hardware!
You do the Fun Part, the Art Work when you apply the Facing Materials!
You Will Find GateBuilder Gate Frames are Better Than You Ever Expected
View a Customers Side Show of a Beautiful Wooden Gate that He Built on GateBuilder Frames
The Wooden Fencing Panels Utilized on these Gates Were Purchased from Home Depot
Mounted on a GateBuilder 'X' Gate 16' Modular Frame
Contractors & Gate Builders,
I'm Tony Whyte Owner & General Manager of the
Victoria House Company. We Manufacture Gates under the Trade Names
Southern Crossings Gates & GateBuilder Gate Frames.
We have superior products that are not well known. We
have exhibited from time to time at Home Shows and the Southern
California Landscape Contractors Expo. Our products have been well
received and it's time to broaden our product reach.
The modularity of our frames is its real strength. The
system is stronger than welded frames and much easier to install.
Because our frames are modular they are also well suited to shipping at
reasonable cost.
GateBuilder Frames are superior in strength because they
are a true truss system as would be engineered for roof trusses or
bridge construction. They are built of heavy duty materials that
parlay into an amazingly light Wooden Gate once the wood facing
material is applied. A GateBuilder frame is guaranteed not to sag
and will outlast many generations of refacing.
If you are a Contractor, you have never installed a gate that will be easier or better performing.
We would like to be your Gate Supplier of Choice - Please give me a call
619 729 0420 or 619 445 8550
Sincerely,
Tony Whyte
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Happiness is Building a Gate With a GateBuilder Gate Frame
Fully Adjustable to fit your gate opening!
Order Today RIGHT NOW!
Includes the Cost of Shipping
619 445 1135 619 729-0420
gatebuilder@hotmail.com
Subscribe to:
Posts (Atom)