Saturday, January 15, 2011
Contractor Gate Supply: GateBuilder - Try Us - You'll be Glad You Did
Contractor Gate Supply: GateBuilder - Try Us - You'll be Glad You Did: "Good Morning Contractors, I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates und..."
GateBuilder - Try Us - You'll be Glad You Did
Good Morning Contractors,
I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates under the Trade Names Southern Crossings Gates & GateBuilder Gate Frames.
We have superior products that are not well known. We have exhibited from time to time at Home Shows and the Southern California Landscape Contractors Expo. Our products have been well received and it's time to broaden our product reach.
The modularity of our frames is its real strength. The system is stronger than welded frames and much easier to install. Because our frames are modular they are also well suited to shipping at reasonable cost.
GateBuilder Frames are superior in strength because they are a true truss system as would be engineered for roof trusses or bridge construction. They are built of heavy duty materials that parlay into an amazingly light Wooden Gate once the wood facing material is applied. A GateBuilder frame is guaranteed not to sag and will outlast many generations of refacing.
If you are a Contractor, you have never installed a gate that will be easier or better performing.
We would like to be your Gate Supplier of Choice - Please give me a call
619 729 0420 or 619 445 8550
Sincerely,
Tony Whyte
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates under the Trade Names Southern Crossings Gates & GateBuilder Gate Frames.
We have superior products that are not well known. We have exhibited from time to time at Home Shows and the Southern California Landscape Contractors Expo. Our products have been well received and it's time to broaden our product reach.
The modularity of our frames is its real strength. The system is stronger than welded frames and much easier to install. Because our frames are modular they are also well suited to shipping at reasonable cost.
GateBuilder Frames are superior in strength because they are a true truss system as would be engineered for roof trusses or bridge construction. They are built of heavy duty materials that parlay into an amazingly light Wooden Gate once the wood facing material is applied. A GateBuilder frame is guaranteed not to sag and will outlast many generations of refacing.
If you are a Contractor, you have never installed a gate that will be easier or better performing.
We would like to be your Gate Supplier of Choice - Please give me a call
619 729 0420 or 619 445 8550
Sincerely,
Tony Whyte
Call Us We're Here to Talk About Your Gate Project
Steel Fully Trussed Gate Frames
Modular Kits - Free Shipping
We Size them to Your Need!
Order today:
619 445 1135 or 619 729 0420
victoriahousecompany.com
gatebuilder@hotmail.com
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Contractor Gate Supply: Introducing GateBuilder Gate Kits - Superior Produ...
Contractor Gate Supply: Introducing GateBuilder Gate Kits - Superior Produ...: "Good Morning Contractors, I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates und..."
Contractor Gate Supply: Reaching Out to the Construction Community
Contractor Gate Supply: Reaching Out to the Construction Community: "Good Morning Contractors, I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates und..."
Reaching Out to the Construction Community
Good Morning Contractors,
I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates under the Trade Names Southern Crossings Gates & GateBuilder Gate Frames.
We have superior products that are not well known. We have exhibited from time to time at Home Shows and the Southern California Landscape Contractors Expo. Our products have been well received and it's time to broaden our product reach.
The modularity of our frames is its real strength. The system is stronger than welded frames and much easier to install. Because our frames are modular they are also well suited to shipping at reasonable cost.
GateBuilder Frames are superior in strength because they are a true truss system as would be engineered for roof trusses or bridge construction. They are built of heavy duty materials that parlay into an amazingly light Wooden Gate once the wood facing material is applied. A GateBuilder frame is guaranteed not to sag and will outlast many generations of refacing.
If you are a Contractor, you have never installed a gate that will be easier or better performing.
We would like to be your Gate Supplier of Choice - Please give me a call
619 729 0420 or 619 445 8550
Sincerely,
Tony Whyte
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates under the Trade Names Southern Crossings Gates & GateBuilder Gate Frames.
We have superior products that are not well known. We have exhibited from time to time at Home Shows and the Southern California Landscape Contractors Expo. Our products have been well received and it's time to broaden our product reach.
The modularity of our frames is its real strength. The system is stronger than welded frames and much easier to install. Because our frames are modular they are also well suited to shipping at reasonable cost.
GateBuilder Frames are superior in strength because they are a true truss system as would be engineered for roof trusses or bridge construction. They are built of heavy duty materials that parlay into an amazingly light Wooden Gate once the wood facing material is applied. A GateBuilder frame is guaranteed not to sag and will outlast many generations of refacing.
If you are a Contractor, you have never installed a gate that will be easier or better performing.
We would like to be your Gate Supplier of Choice - Please give me a call
619 729 0420 or 619 445 8550
Sincerely,
Tony Whyte
Call Us We're Here to Talk About Your Gate Project
Steel Fully Trussed Gate Frames
Modular Kits - Free Shipping
We Size them to Your Need!
Order today:
619 445 1135 or 619 729 0420
victoriahousecompany.com
gatebuilder@hotmail.com
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Gate Kit: The Prayer for Today
Gate Kit: The Prayer for Today: "Good Morning Contractors, The economy has taken a toll on our families and our businesses. With the collapse of the building industry the..."
RV Gate: You'd rather stay in a hotel than open that gate t...
RV Gate: You'd rather stay in a hotel than open that gate t...: "If you'd rather stay in a hotel than open that gate to drive your RV?Order GateBuilder its strong light easy to open now and will be easy t..."
Gate Kit: GateBuilder - Refreshing New Product
Gate Kit: GateBuilder - Refreshing New Product: "Filling the Need for Quality Gate Products Wide Wooden Gates are Our Speciality Automatic Gate Openers can be used with a GateBuilde..."
Gate Kit: Are You a Wood Worker - Gate Builder Frames Will ...
Gate Kit: Are You a Wood Worker - Gate Builder Frames Will ...: "We Make the Frame, Supply the Hardware! You do the Fun Part, the Art Work when you apply the Facing Materials! GateBuilder II $129.00..."
Wide Wood Gate: We're Not the Big Boy on the Block - But We're Bet...
Wide Wood Gate: We're Not the Big Boy on the Block - But We're Bet...: "Filling the Need for Quality Gate Products Wide Wooden Gates are Our Speciality Automatic Gate Openers can be used with a GateBuilde..."
Wide Wood Gate: Think You Should Buy a Gate at Home Depot?
Wide Wood Gate: Think You Should Buy a Gate at Home Depot?: "'That's Just Wrong' Good Morning, I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufac..."
Wide Wood Gate: A Quality Gate Frame Is Hard to Find
Wide Wood Gate: A Quality Gate Frame Is Hard to Find: "That's Why We Build Them 'Because Home Depot and Lowes Don't Sell Quality Frames' Wide Wooden Gates are Our Speciality Automatic Gate Ope..."
Wide Wood Gate: A Prayer on Behalf of Those in the Construction In...
Wide Wood Gate: A Prayer on Behalf of Those in the Construction In...: "Good Morning Contractors, The economy has taken a toll on our families and our businesses. With the collapse of the building industry the..."
Wide Wood Gate: I Just Got Tired of Gravity Ruining My Workmanship...
Wide Wood Gate: I Just Got Tired of Gravity Ruining My Workmanship...: "Designed by a Former Gate Installer Who Figured out How to Do It BetterImagine a Gate that will never Sag We Make the Frame, Supply the Ha..."
Contractor Gate Supply: What is the Best Place to Buy a Gate Frame?
Contractor Gate Supply: What is the Best Place to Buy a Gate Frame?: "Winning Combo Strength & Price GateBuilder Gate Frames The Best Source of Gate Frames Hands Down Good Morning Con..."
Contractor Gate Supply: What is the Best Place to Buy a Gate Frame?
Contractor Gate Supply: What is the Best Place to Buy a Gate Frame?: "Winning Combo Strength & Price GateBuilder Gate Frames The Best Source of Gate Frames Hands Down Good Morning Con..."
What is the Best Place to Buy a Gate Frame?
Winning Combo Strength & Price
GateBuilder Gate Frames
The Best Source of Gate Frames Hands Down
Good Morning Contractors,
I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates under the Trade Names Southern Crossings Gates & GateBuilder Gate Frames.
The modularity of our frames is its real strength. The system is stronger than welded frames and much easier to install. Because our frames are modular they are also well suited to shipping at reasonable cost.
GateBuilder Frames are superior in strength because they are a true truss system as would be engineered for roof trusses or bridge construction. They are built of heavy duty materials that parlay into an amazingly light Wooden Gate once the wood facing material is applied. A GateBuilder frame is guaranteed not to sag and will outlast many generations of refacing.
If you are a Contractor, you have never installed a gate that will be easier or better performing.
We would like to be your Gate Supplier of Choice - Please give me a call
619 729 0420 or 619 445 8550
Sincerely,
Tony Whyte
Call Us We're Here to Talk About Your Gate Project
Steel Fully Trussed Gate Frames
Modular Kits - Free Shipping
We Size them to Your Need!
Order today:
619 445 1135 or 619 729 0420
victoriahousecompany.com
gatebuilder@hotmail.com
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Contractor Gate Supply: A Message Worth Sharing with Friends & Neighbors
Contractor Gate Supply: A Message Worth Sharing with Friends & Neighbors: "Superior Gate Products GateBuilder Gate Frames Hi, I'm Tony Whyte Owner & General Manager of the Victoria House Company..."
A Message Worth Sharing with Friends & Neighbors
Superior Gate Products
GateBuilder Gate Frames
Hi,
I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates under the Trade Names Southern Crossings Gates & GateBuilder Gate Frames.
The modularity of our frames is its real strength. The system is stronger than welded frames and much easier to install. Because our frames are modular they are also well suited to shipping at reasonable cost.
GateBuilder Frames are superior in strength because they are a true truss system as would be engineered for roof trusses or bridge construction. They are built of heavy duty materials that parlay into an amazingly light Wooden Gate once the wood facing material is applied. A GateBuilder frame is guaranteed not to sag and will outlast many generations of refacing.
If you are a Contractor, you have never installed a gate that will be easier or better performing.
We would like to be your Gate Supplier of Choice - Please give me a call
619 729 0420 or 619 445 8550
Sincerely,
Tony Whyte
Call Us We're Here to Talk About Your Gate Project
Steel Fully Trussed Gate Frames
Modular Kits - Free Shipping
We Size them to Your Need!
Order today:
619 445 1135 or 619 729 0420
victoriahousecompany.com
gatebuilder@hotmail.com
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Contractor Gate Supply: I'm a Landscape Contractor - I've found a Terrific...
Contractor Gate Supply: I'm a Landscape Contractor - I've found a Terrific...: "Contractors please take note. GateBuilder can make your life a lot easier and your finished product a lot better. Easy to..."
Contractor Gate Supply: Winning Combo Strength & Price "Supersize It?"
Contractor Gate Supply: Winning Combo Strength & Price "Supersize It?": "Winning Combo Strength & Price - 'Supersize It?' Good Morning Contractors, I'm Tony Whyte Owner & General Manager of ..."
Contractor Gate Supply: Winning Combo Strength & Price "Supersize It?"
Contractor Gate Supply: Winning Combo Strength & Price "Supersize It?": "Winning Combo Strength & Price - 'Supersize It?' Good Morning Contractors, I'm Tony Whyte Owner & General Manager of ..."
Contractor Gate Supply: Our Legacy is Satisfied Customers
Contractor Gate Supply: Our Legacy is Satisfied Customers: "Good Morning Contractors, I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates und..."
Contractor Gate Supply: Spans the Distance - Carries the Weight
Contractor Gate Supply: Spans the Distance - Carries the Weight: "Good Morning Contractors, I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates und..."
Contractor Gate Supply: GateBuilder - An Investment; NOT an expense
Contractor Gate Supply: GateBuilder - An Investment; NOT an expense: "Good Morning Contractors, I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates und..."
Contractor Gate Supply: If I Was a Gate, What Brand Would I Like to Be?
Contractor Gate Supply: If I Was a Gate, What Brand Would I Like to Be?: "Good Morning Contractors, I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates und..."
Contractor Gate Supply: We're the Gate Builders - We're "GateBuilder"
Contractor Gate Supply: We're the Gate Builders - We're "GateBuilder": " Think You Should Buy That Gate a Home Depot or Lowes? Good Morning, I'm Tony Whyte Owner & General Manager of the Vi..."
Contractor Gate Supply: Hardscape Contractors STEP UP
Contractor Gate Supply: Hardscape Contractors STEP UP: "Good Morning Hardscape Contractors, I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture..."
Contractor Gate Supply: A Prayer for You in the Construction Industry
Contractor Gate Supply: A Prayer for You in the Construction Industry: "Good Morning Contractors, The economy has taken a toll on our families and our businesses. With the collapse of the building industry the..."
Contractor Gate Supply: Think You Should Buy a Gate at Home Depot?
Contractor Gate Supply: Think You Should Buy a Gate at Home Depot?: "'That's Just Wrong' Good Morning, I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufac..."
Contractor Gate Supply: "I Had So Much Fun Building My Gate"
Contractor Gate Supply: "I Had So Much Fun Building My Gate": " Customer Wrote: I Bought GateBuilder. I had So Much Fun Building My New Gate. I am Really Happy!' Good Morning, I..."
Contractor Gate Supply: Gates to Die For!
Contractor Gate Supply: Gates to Die For!: "Good Morning, I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates under the T..."
Contractor Gate Supply: Strongest Frame Available - We Build Them Strong
Contractor Gate Supply: Strongest Frame Available - We Build Them Strong: "14 Gauge (.088) Steel Frame'Best Frame Available'We're Here Today to Take Your Order Fully Trussed Gate FramesModular Kits - Free Shi..."
Contractor Gate Supply: A Prayer on Behalf of Those in the Construction In...
Contractor Gate Supply: A Prayer on Behalf of Those in the Construction In...: "Good Morning Contractors, The economy has taken a toll on our families and our businesses. With the collapse of the building industry the..."
Contractor Gate Supply: Gate Builder Found Jazzed!
Contractor Gate Supply: Gate Builder Found Jazzed!: " A Client Wrote: I'm Really Jazzed, GateBuilder Is All They Say It Is! In this World, That's Really..."
Contractor Gate Supply: I Just Got Tired of Gravity Ruining My Workmanship...
Contractor Gate Supply: I Just Got Tired of Gravity Ruining My Workmanship...: "Designed by a Former Gate Installer Who Figured out How to Do It BetterImagine a Gate that will never Sag We Make the Frame, Supply the Ha..."
Contractor Gate Supply: Was Your Gate Constructed to Fail?
Contractor Gate Supply: Was Your Gate Constructed to Fail?: "If You Didn't Use a GateBuilder Frame it Surly Was! Build It or Rebuild It with GateBuilder GateBuilderSteel Fully Trussed Gate Frames..."
Contractor Gate Supply: Was Your Gate Constructed to Fail?
Contractor Gate Supply: Was Your Gate Constructed to Fail?: "If You Didn't Use a GateBuilder Frame it Surly Was! Build It or Rebuild It with GateBuilder GateBuilderSteel Fully Trussed Gate Frames..."
Gate Kit: Gate Kits - The Best for Less!
Gate Kit: Gate Kits - The Best for Less!: "The Victoria House Company Manufacturer and Distributor of GateBuilder Gate Kitsvictoriahousecompany.com gatebuilder@hotmail.com 6..."
Contractor Gate Supply: Wide is Hard - It's all in the Frame
Contractor Gate Supply: Wide is Hard - It's all in the Frame: "14 Gauge (.088) Steel Frame'Best Frame Available'We're Here Today to Take Your Order Fully Trussed Gate FramesModular Kits - Free Shi..."
Wide is Hard - It's all in the Frame
14 Gauge (.088) Steel Frame
"Best Frame Available"
We're Here Today to Take Your Order
Fully Trussed Gate Frames
Modular Kits - Free Shipping
We Size them to Your Need!
Order today:
619 445 1135 or 619 729 0420
victoriahousecompany.com
gatebuilder@hotmail.com
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Wide Wood Gate: Buying a Gate? You Get What You Pay For
Wide Wood Gate: Buying a Gate? You Get What You Pay For: " Think You Should Buy That Gate a Home Depot or Lowes? Good Morning, I'm Tony Whyte Owner & General Manager of the Vi..."
Contractor Gate Supply: Spring Projects - Are You Planning Ahead?
Contractor Gate Supply: Spring Projects - Are You Planning Ahead?: "Spring is Just Around the Corner Start Planning Your Spring Projects Now! - We Can Help!Fully Trussed Modular Gate System ..."
Wide Wood Gate: A Prayer on Behalf of Those in the Construction In...
Wide Wood Gate: A Prayer on Behalf of Those in the Construction In...: "Good Morning Contractors, The economy has taken a toll on our families and our businesses. With the collapse of the building industry the..."
Contractor Gate Supply: A Prayer for You in the Construction Industry
Contractor Gate Supply: A Prayer for You in the Construction Industry: "Good Morning Contractors, The economy has taken a toll on our families and our businesses. With the collapse of the building industry the..."
Contractor Gate Supply: A Prayer on Behalf of Those in the Construction In...
Contractor Gate Supply: A Prayer on Behalf of Those in the Construction In...: "Good Morning Contractors, The economy has taken a toll on our families and our businesses. With the collapse of the building industry the..."
Gate Kit: A Prayer on Behalf of Those in the Construction In...
Gate Kit: A Prayer on Behalf of Those in the Construction In...: "Good Morning Contractors, The economy has taken a toll on our families and our businesses. With the collapse of the building industry the..."
Contractor Gate Supply: I'm a Better Gate Builder now that I Use "GATEBUIL...
Contractor Gate Supply: I'm a Better Gate Builder now that I Use "GATEBUIL...: "GateBuilder Has Made Me a Much Better Gate Builder 14 Gauge (.088) Steel Frame'Best Frame Available'We're Here Today to Take Your Order &nbs..."
I'm a Better Gate Builder now that I Use "GATEBUILDER FRAMES"
GateBuilder Has Made Me a Much Better Gate Builder
14 Gauge (.088) Steel Frame
"Best Frame Available"
We're Here Today to Take Your Order
Fully Trussed Gate Frames
Modular Kits - Free Shipping
We Size them to Your Need!
Order today:
619 445 1135 or 619 729 0420
victoriahousecompany.com
gatebuilder@hotmail.com
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Contractor Gate Supply: If I Knew Then What I Know Now
Contractor Gate Supply: If I Knew Then What I Know Now: "If I Knew Then What I Know Now I'd Have Used GateBuilder When I built My Gate Finest Materials14 Gauge (.088) Steel Frame'Best Frame Availab..."
If I Knew Then What I Know Now
If I Knew Then What I Know Now
I'd Have Used GateBuilder When I built My Gate
Finest Materials
14 Gauge (.088) Steel Frame
"Best Frame Available"
We're Here Today to Take Your Order
Fully Trussed Gate Frames
Modular Kits - Free Shipping
We Size them to Your Need!
Order today:
619 445 1135 or 619 729 0420
victoriahousecompany.com
gatebuilder@hotmail.com
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Contractor Gate Supply: Keeping Clients Happy is a Full Time Job
Contractor Gate Supply: Keeping Clients Happy is a Full Time Job: "My Client Just Wasn't Happy With the Gate I Installed! I sure wish I'd installed GateBuilder Adjust a Gate vs GateBuild..."
Contractor Gate Supply: I'm a Landscape Contractor - I've found a Terrific...
Contractor Gate Supply: I'm a Landscape Contractor - I've found a Terrific...: "Contractors please take note. GateBuilder can make your life a lot easier and your finished product a lot better. Easy to..."
Contractor Gate Supply: I Just Got Tired of Gravity Ruining My Workmanship...
Contractor Gate Supply: I Just Got Tired of Gravity Ruining My Workmanship...: "Designed by a Former Gate Installer Who Figured out How to Do It BetterImagine a Gate that will never Sag We Make the Frame, Supply the Ha..."
Contractor Gate Supply: Ordering GateBuilder is Easy - Just Call 619 729 0...
Contractor Gate Supply: Ordering GateBuilder is Easy - Just Call 619 729 0...: "14 Gauge (.088) Steel Frame'Best Frame Available'We're Here Today to Take Your Order Fully Trussed Gate FramesModular Kits - Free Shi..."
Ordering GateBuilder is Easy - Call 619 729 0420
14 Gauge (.088) Steel Frame
"Best Frame Available"
We're Here Today to Take Your Order
Fully Trussed Gate Frames
Modular Kits - Free Shipping
We Size them to Your Need!
Order today:
619 445 1135 or 619 729 0420
victoriahousecompany.com
gatebuilder@hotmail.com
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Contractor Gate Supply: Landscape Contractors - We are Service - We are Ga...
Contractor Gate Supply: Landscape Contractors - We are Service - We are Ga...: "14 Gauge (.088) Steel Frame'Best Frame Available'We're Here Today to Take Your Order Fully Trussed Gate FramesModular Kits - Free Shi..."
Contractor Gate Supply: Landscape Contractors - We are Service - We are Ga...
Contractor Gate Supply: Landscape Contractors - We are Service - We are Ga...: "14 Gauge (.088) Steel Frame'Best Frame Available'We're Here Today to Take Your Order Fully Trussed Gate FramesModular Kits - Free Shi..."
Landscape Contractors - We are Service - We are GateBuilder
14 Gauge (.088) Steel Frame
"Best Frame Available"
We're Here Today to Take Your Order
Fully Trussed Gate Frames
Modular Kits - Free Shipping
We Size them to Your Need!
Order today:
619 445 1135 or 619 729 0420
victoriahousecompany.com
gatebuilder@hotmail.com
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Contractor Gate Supply: Strongest Frame Available - We Build Them Strong
Contractor Gate Supply: Strongest Frame Available - We Build Them Strong: "14 Gauge (.088) Steel Frame'Best Frame Available'We're Here Today to Take Your Order Fully Trussed Gate FramesModular Kits - Free Shi..."
Strongest Frame Available - We Build Them Strong
14 Gauge (.088) Steel Frame
"Best Frame Available"
We're Here Today to Take Your Order
Fully Trussed Gate Frames
Modular Kits - Free Shipping
We Size them to Your Need!
Order today:
619 445 1135 or 619 729 0420
victoriahousecompany.com
gatebuilder@hotmail.com
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Contractor Gate Supply: Winning Combo Strength & Price - Supersize It
Contractor Gate Supply: Winning Combo Strength & Price - Supersize It: "Winning Combo Strength & Price - 'Supersize It?' Good Morning Contractors, I'm Tony Whyte Owner & General Manager of&nbs..."
Winning Combo Strength & Price - Supersize It
Winning Combo Strength & Price - "Supersize It?"
Good Morning Contractors,
I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates under the Trade Names Southern Crossings Gates & GateBuilder Gate Frames.
We have superior products that are not well known. We have exhibited from time to time at Home Shows and the Southern California Landscape Contractors Expo. Our products have been well received and it's time to broaden our product reach.
The modularity of our frames is its real strength. The system is stronger than welded frames and much easier to install. Because our frames are modular they are also well suited to shipping at reasonable cost.
GateBuilder Frames are superior in strength because they are a true truss system as would be engineered for roof trusses or bridge construction. They are built of heavy duty materials that parlay into an amazingly light Wooden Gate once the wood facing material is applied. A GateBuilder frame is guaranteed not to sag and will outlast many generations of refacing.
If you are a Contractor, you have never installed a gate that will be easier or better performing.
We would like to be your Gate Supplier of Choice - Please give me a call
619 729 0420 or 619 445 8550
Sincerely,
Tony Whyte
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Good Morning Contractors,
I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates under the Trade Names Southern Crossings Gates & GateBuilder Gate Frames.
The modularity of our frames is its real strength. The system is stronger than welded frames and much easier to install. Because our frames are modular they are also well suited to shipping at reasonable cost.
GateBuilder Frames are superior in strength because they are a true truss system as would be engineered for roof trusses or bridge construction. They are built of heavy duty materials that parlay into an amazingly light Wooden Gate once the wood facing material is applied. A GateBuilder frame is guaranteed not to sag and will outlast many generations of refacing.
If you are a Contractor, you have never installed a gate that will be easier or better performing.
We would like to be your Gate Supplier of Choice - Please give me a call
619 729 0420 or 619 445 8550
Sincerely,
Tony Whyte
Call Us We're Here to Talk About Your Gate Project
Steel Fully Trussed Gate Frames
Modular Kits - Free Shipping
We Size them to Your Need!
Order today:
619 445 1135 or 619 729 0420
victoriahousecompany.com
gatebuilder@hotmail.com
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Contractor Gate Supply: "I Had So Much Fun Building My Gate"
Contractor Gate Supply: "I Had So Much Fun Building My Gate": " Customer Wrote: I Bought GateBuilder. I had So Much Fun Building My New Gate. I am Really Happy!' Good Morning, I..."
"I Had So Much Fun Building My Gate"
Customer Wrote: I Bought GateBuilder. I had So Much Fun Building My New Gate. I am Really Happy!"
Good Morning,
I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates under the Trade Names Southern Crossings Gates & GateBuilder Gate Frames.
We have superior products that are not well known. We have exhibited from time to time at Home Shows and the Southern California Landscape Contractors Expo. Our products have been well received and it's time to broaden our product reach.
The modularity of our frames is its real strength. The system is stronger than welded frames and much easier to install. Because our frames are modular they are also well suited to shipping at reasonable cost.
GateBuilder Frames are superior in strength because they are a true truss system as would be engineered for roof trusses or bridge construction. They are built of heavy duty materials that parlay into an amazingly light Wooden Gate once the wood facing material is applied. A GateBuilder frame is guaranteed not to sag and will outlast many generations of refacing.
If you are a Contractor, you have never installed a gate that will be easier or better performing.
We would like to be your Gate Supplier of Choice - Please give me a call
619 729 0420 or 619 445 8550
Sincerely,
Tony Whyte
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Good Morning,
I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates under the Trade Names Southern Crossings Gates & GateBuilder Gate Frames.
We have superior products that are not well known. We have exhibited from time to time at Home Shows and the Southern California Landscape Contractors Expo. Our products have been well received and it's time to broaden our product reach.
The modularity of our frames is its real strength. The system is stronger than welded frames and much easier to install. Because our frames are modular they are also well suited to shipping at reasonable cost.
GateBuilder Frames are superior in strength because they are a true truss system as would be engineered for roof trusses or bridge construction. They are built of heavy duty materials that parlay into an amazingly light Wooden Gate once the wood facing material is applied. A GateBuilder frame is guaranteed not to sag and will outlast many generations of refacing.
If you are a Contractor, you have never installed a gate that will be easier or better performing.
We would like to be your Gate Supplier of Choice - Please give me a call
619 729 0420 or 619 445 8550
Sincerely,
Tony Whyte
Call Us We're Here to Talk About Your Gate Project
Steel Fully Trussed Gate Frames
Modular Kits - Free Shipping
We Size them to Your Need!
Order today:
619 445 1135 or 619 729 0420
victoriahousecompany.com
gatebuilder@hotmail.com
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Contractor Gate Supply: We're the Gate Builders - We're "GateBuilder"
Contractor Gate Supply: We're the Gate Builders - We're "GateBuilder": " Think You Should Buy That Gate a Home Depot or Lowes? Good Morning, I'm Tony Whyte Owner & General Manager of the Vi..."
We're the Gate Builders - We're "GateBuilder"
Think You Should Buy That Gate a Home Depot or Lowes?
Good Morning,
I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates under the Trade Names Southern Crossings Gates & GateBuilder Gate Frames.
We have superior products that are not well known. We have exhibited from time to time at Home Shows and the Southern California Landscape Contractors Expo. Our products have been well received and it's time to broaden our product reach.
The modularity of our frames is its real strength. The system is stronger than welded frames and much easier to install. Because our frames are modular they are also well suited to shipping at reasonable cost.
GateBuilder Frames are superior in strength because they are a true truss system as would be engineered for roof trusses or bridge construction. They are built of heavy duty materials that parlay into an amazingly light Wooden Gate once the wood facing material is applied. A GateBuilder frame is guaranteed not to sag and will outlast many generations of refacing.
If you are a Contractor, you have never installed a gate that will be easier or better performing.
We would like to be your Gate Supplier of Choice - Please give me a call
619 729 0420 or 619 445 8550
Sincerely,
Tony Whyte
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Good Morning,
I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates under the Trade Names Southern Crossings Gates & GateBuilder Gate Frames.
We have superior products that are not well known. We have exhibited from time to time at Home Shows and the Southern California Landscape Contractors Expo. Our products have been well received and it's time to broaden our product reach.
The modularity of our frames is its real strength. The system is stronger than welded frames and much easier to install. Because our frames are modular they are also well suited to shipping at reasonable cost.
GateBuilder Frames are superior in strength because they are a true truss system as would be engineered for roof trusses or bridge construction. They are built of heavy duty materials that parlay into an amazingly light Wooden Gate once the wood facing material is applied. A GateBuilder frame is guaranteed not to sag and will outlast many generations of refacing.
If you are a Contractor, you have never installed a gate that will be easier or better performing.
We would like to be your Gate Supplier of Choice - Please give me a call
619 729 0420 or 619 445 8550
Sincerely,
Tony Whyte
Call Us We're Here to Talk About Your Gate Project
Steel Fully Trussed Gate Frames
Modular Kits - Free Shipping
We Size them to Your Need!
Order today:
619 445 1135 or 619 729 0420
victoriahousecompany.com
gatebuilder@hotmail.com
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Contractor Gate Supply: Buying a Gate? You Get What You Pay For
Contractor Gate Supply: Buying a Gate? You Get What You Pay For: " Think You Should Buy That Gate a Home Depot or Lowes? Good Morning, I'm Tony Whyte Owner & General Manager of the Vi..."
Contractor Gate Supply: Buying a Gate? You Get What You Pay For
Contractor Gate Supply: Buying a Gate? You Get What You Pay For: " Think You Should Buy That Gate a Home Depot or Lowes? Good Morning, I'm Tony Whyte Owner & General Manager of the Vi..."
Buying a Gate? You Get What You Pay For
Think You Should Buy That Gate a Home Depot or Lowes?
Good Morning,
I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates under the Trade Names Southern Crossings Gates & GateBuilder Gate Frames.
We have superior products that are not well known. We have exhibited from time to time at Home Shows and the Southern California Landscape Contractors Expo. Our products have been well received and it's time to broaden our product reach.
The modularity of our frames is its real strength. The system is stronger than welded frames and much easier to install. Because our frames are modular they are also well suited to shipping at reasonable cost.
GateBuilder Frames are superior in strength because they are a true truss system as would be engineered for roof trusses or bridge construction. They are built of heavy duty materials that parlay into an amazingly light Wooden Gate once the wood facing material is applied. A GateBuilder frame is guaranteed not to sag and will outlast many generations of refacing.
If you are a Contractor, you have never installed a gate that will be easier or better performing.
We would like to be your Gate Supplier of Choice - Please give me a call
619 729 0420 or 619 445 8550
Sincerely,
Tony Whyte
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Good Morning,
I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates under the Trade Names Southern Crossings Gates & GateBuilder Gate Frames.
We have superior products that are not well known. We have exhibited from time to time at Home Shows and the Southern California Landscape Contractors Expo. Our products have been well received and it's time to broaden our product reach.
The modularity of our frames is its real strength. The system is stronger than welded frames and much easier to install. Because our frames are modular they are also well suited to shipping at reasonable cost.
GateBuilder Frames are superior in strength because they are a true truss system as would be engineered for roof trusses or bridge construction. They are built of heavy duty materials that parlay into an amazingly light Wooden Gate once the wood facing material is applied. A GateBuilder frame is guaranteed not to sag and will outlast many generations of refacing.
If you are a Contractor, you have never installed a gate that will be easier or better performing.
We would like to be your Gate Supplier of Choice - Please give me a call
619 729 0420 or 619 445 8550
Sincerely,
Tony Whyte
Call Us We're Here to Talk About Your Gate Project
Steel Fully Trussed Gate Frames
Modular Kits - Free Shipping
We Size them to Your Need!
Order today:
619 445 1135 or 619 729 0420
victoriahousecompany.com
gatebuilder@hotmail.com
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Contractor Gate Supply: Think You Should Buy a Gate at Home Depot?
Contractor Gate Supply: Think You Should Buy a Gate at Home Depot?: "'That's Just Wrong' Good Morning, I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufac..."
Think You Should Buy a Gate at Home Depot?
"That's Just Wrong"
Good Morning,
I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates under the Trade Names Southern Crossings Gates & GateBuilder Gate Frames.
We have superior products that are not well known. We have exhibited from time to time at Home Shows and the Southern California Landscape Contractors Expo. Our products have been well received and it's time to broaden our product reach.
The modularity of our frames is its real strength. The system is stronger than welded frames and much easier to install. Because our frames are modular they are also well suited to shipping at reasonable cost.
GateBuilder Frames are superior in strength because they are a true truss system as would be engineered for roof trusses or bridge construction. They are built of heavy duty materials that parlay into an amazingly light Wooden Gate once the wood facing material is applied. A GateBuilder frame is guaranteed not to sag and will outlast many generations of refacing.
If you are a Contractor, you have never installed a gate that will be easier or better performing.
We would like to be your Gate Supplier of Choice - Please give me a call
619 729 0420 or 619 445 8550
Sincerely,
Tony Whyte
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Good Morning,
I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates under the Trade Names Southern Crossings Gates & GateBuilder Gate Frames.
We have superior products that are not well known. We have exhibited from time to time at Home Shows and the Southern California Landscape Contractors Expo. Our products have been well received and it's time to broaden our product reach.
The modularity of our frames is its real strength. The system is stronger than welded frames and much easier to install. Because our frames are modular they are also well suited to shipping at reasonable cost.
GateBuilder Frames are superior in strength because they are a true truss system as would be engineered for roof trusses or bridge construction. They are built of heavy duty materials that parlay into an amazingly light Wooden Gate once the wood facing material is applied. A GateBuilder frame is guaranteed not to sag and will outlast many generations of refacing.
If you are a Contractor, you have never installed a gate that will be easier or better performing.
We would like to be your Gate Supplier of Choice - Please give me a call
619 729 0420 or 619 445 8550
Sincerely,
Tony Whyte
Call Us We're Here to Talk About Your Gate Project
Steel Fully Trussed Gate Frames
Modular Kits - Free Shipping
We Size them to Your Need!
Order today:
619 445 1135 or 619 729 0420
victoriahousecompany.com
gatebuilder@hotmail.com
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Contractor Gate Supply: That's Just Wrong!
Contractor Gate Supply: That's Just Wrong!: "Don't Buy that Gate at Home Depot or Lowes! Good Morning, I'm Tony Whyte Owner & General Manager of the Victoria House Comp..."
Contractor Gate Supply: That's Just Wrong!
Contractor Gate Supply: That's Just Wrong!: "Don't Buy that Gate at Home Depot or Lowes! Good Morning, I'm Tony Whyte Owner & General Manager of the Victoria House Comp..."
That's Just Wrong!
Don't Buy that Gate at Home Depot or Lowes!
Good Morning,
I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates under the Trade Names Southern Crossings Gates & GateBuilder Gate Frames.
We have superior products that are not well known. We have exhibited from time to time at Home Shows and the Southern California Landscape Contractors Expo. Our products have been well received and it's time to broaden our product reach.
The modularity of our frames is its real strength. The system is stronger than welded frames and much easier to install. Because our frames are modular they are also well suited to shipping at reasonable cost.
GateBuilder Frames are superior in strength because they are a true truss system as would be engineered for roof trusses or bridge construction. They are built of heavy duty materials that parlay into an amazingly light Wooden Gate once the wood facing material is applied. A GateBuilder frame is guaranteed not to sag and will outlast many generations of refacing.
If you are a Contractor, you have never installed a gate that will be easier or better performing.
We would like to be your Gate Supplier of Choice - Please give me a call
619 729 0420 or 619 445 8550
Sincerely,
Tony Whyte
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Good Morning,
I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates under the Trade Names Southern Crossings Gates & GateBuilder Gate Frames.
We have superior products that are not well known. We have exhibited from time to time at Home Shows and the Southern California Landscape Contractors Expo. Our products have been well received and it's time to broaden our product reach.
The modularity of our frames is its real strength. The system is stronger than welded frames and much easier to install. Because our frames are modular they are also well suited to shipping at reasonable cost.
GateBuilder Frames are superior in strength because they are a true truss system as would be engineered for roof trusses or bridge construction. They are built of heavy duty materials that parlay into an amazingly light Wooden Gate once the wood facing material is applied. A GateBuilder frame is guaranteed not to sag and will outlast many generations of refacing.
If you are a Contractor, you have never installed a gate that will be easier or better performing.
We would like to be your Gate Supplier of Choice - Please give me a call
619 729 0420 or 619 445 8550
Sincerely,
Tony Whyte
Call Us We're Here to Talk About Your Gate Project
Steel Fully Trussed Gate Frames
Modular Kits - Free Shipping
We Size them to Your Need!
Order today:
619 445 1135 or 619 729 0420
victoriahousecompany.com
gatebuilder@hotmail.com
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Contractor Gate Supply: Gates to Die For!
Contractor Gate Supply: Gates to Die For!: "Good Morning, I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates under the T..."
Contractor Gate Supply: Gates to Die For!
Contractor Gate Supply: Gates to Die For!: "Good Morning, I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates under the T..."
Gates to Die For!
Good Morning,
I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates under the Trade Names Southern Crossings Gates & GateBuilder Gate Frames.
We have superior products that are not well known. We have exhibited from time to time at Home Shows and the Southern California Landscape Contractors Expo. Our products have been well received and it's time to broaden our product reach.
The modularity of our frames is its real strength. The system is stronger than welded frames and much easier to install. Because our frames are modular they are also well suited to shipping at reasonable cost.
GateBuilder Frames are superior in strength because they are a true truss system as would be engineered for roof trusses or bridge construction. They are built of heavy duty materials that parlay into an amazingly light Wooden Gate once the wood facing material is applied. A GateBuilder frame is guaranteed not to sag and will outlast many generations of refacing.
If you are a Contractor, you have never installed a gate that will be easier or better performing.
We would like to be your Gate Supplier of Choice - Please give me a call
619 729 0420 or 619 445 8550
Sincerely,
Tony Whyte
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates under the Trade Names Southern Crossings Gates & GateBuilder Gate Frames.
We have superior products that are not well known. We have exhibited from time to time at Home Shows and the Southern California Landscape Contractors Expo. Our products have been well received and it's time to broaden our product reach.
The modularity of our frames is its real strength. The system is stronger than welded frames and much easier to install. Because our frames are modular they are also well suited to shipping at reasonable cost.
GateBuilder Frames are superior in strength because they are a true truss system as would be engineered for roof trusses or bridge construction. They are built of heavy duty materials that parlay into an amazingly light Wooden Gate once the wood facing material is applied. A GateBuilder frame is guaranteed not to sag and will outlast many generations of refacing.
If you are a Contractor, you have never installed a gate that will be easier or better performing.
We would like to be your Gate Supplier of Choice - Please give me a call
619 729 0420 or 619 445 8550
Sincerely,
Tony Whyte
Call Us We're Here to Talk About Your Gate Project
Steel Fully Trussed Gate Frames
Modular Kits - Free Shipping
We Size them to Your Need!
Order today:
619 445 1135 or 619 729 0420
victoriahousecompany.com
gatebuilder@hotmail.com
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Contractor Gate Supply: We Build the Best & We Build Them for You
Contractor Gate Supply: We Build the Best & We Build Them for You: "Good Morning, I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates under the T..."
We Build the Best & We Build Them for You
Good Morning,
I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates under the Trade Names Southern Crossings Gates & GateBuilder Gate Frames.
We have superior products that are not well known. We have exhibited from time to time at Home Shows and the Southern California Landscape Contractors Expo. Our products have been well received and it's time to broaden our product reach.
The modularity of our frames is its real strength. The system is stronger than welded frames and much easier to install. Because our frames are modular they are also well suited to shipping at reasonable cost.
GateBuilder Frames are superior in strength because they are a true truss system as would be engineered for roof trusses or bridge construction. They are built of heavy duty materials that parlay into an amazingly light Wooden Gate once the wood facing material is applied. A GateBuilder frame is guaranteed not to sag and will outlast many generations of refacing.
If you are a Contractor, you have never installed a gate that will be easier or better performing.
We would like to be your Gate Supplier of Choice - Please give me a call
619 729 0420 or 619 445 8550
Sincerely,
Tony Whyte
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
I'm Tony Whyte Owner & General Manager of the Victoria House Company. We Manufacture Gates under the Trade Names Southern Crossings Gates & GateBuilder Gate Frames.
We have superior products that are not well known. We have exhibited from time to time at Home Shows and the Southern California Landscape Contractors Expo. Our products have been well received and it's time to broaden our product reach.
The modularity of our frames is its real strength. The system is stronger than welded frames and much easier to install. Because our frames are modular they are also well suited to shipping at reasonable cost.
GateBuilder Frames are superior in strength because they are a true truss system as would be engineered for roof trusses or bridge construction. They are built of heavy duty materials that parlay into an amazingly light Wooden Gate once the wood facing material is applied. A GateBuilder frame is guaranteed not to sag and will outlast many generations of refacing.
If you are a Contractor, you have never installed a gate that will be easier or better performing.
We would like to be your Gate Supplier of Choice - Please give me a call
619 729 0420 or 619 445 8550
Sincerely,
Tony Whyte
Call Us We're Here to Talk About Your Gate Project
Steel Fully Trussed Gate Frames
Modular Kits - Free Shipping
We Size them to Your Need!
Order today:
619 445 1135 or 619 729 0420
victoriahousecompany.com
gatebuilder@hotmail.com
Steel Gate Frame for Wood & Vinyl Gates
"Beats Adjust-A-Gate Hands Down"
Steel for Strength! Trussing in both Compression & Tension prevents sag!
Gates are hung in cantilever. This means that the gate is supported at only one end. Because of this, especially for wider gates, the hinges must be strong, the frame must be strong and solid cross bracing within the frame is a must.
Most gate frames utilize a cable that spans from the top hinge corner to the bottom corner of the unsupported end of the gate. This approach attempts to control sag through tension by holding up the bottom corner of the unsupported end of the gate. This approach only addresses the force of tension that is being placed on the gate, but ignores the considerable compression force that is in play when a gate is installed. An approach, that only addresses tension, will work for a while until the cable stretches and/or the corners give way. The only way that this approach will work over time, is to install a support foot or wheel for the gate at the unsupported end.
A gate built with a true truss frame utilizes strong hinges, a strong frame with solid corner connections, and solid cross bracing (that cannot stretch) that extends from corner to corner each way. This addresses the forces of both tension and compression that is placed on the gate once it is installed. With this approach, a support foot or wheel will not be required.
Most of the popular steel gate frames offered for sale in the market are not utilizing true truss technology which is required to effectively address gate sag. .
Subscribe to:
Posts (Atom)